AMX RDM-FDB Manuale Utente Scaricare il pdf

Installation Sheet

RDM-FDB Single Channel Lutron FDB Ballast Dimmer

1920 W

The RDM-FDB Single Channel Ballast Dimmer is a 1920 W positive air gap

relay and dimmer, built for strength and for reliable switching/dimming of

Lutron FDB ballasts. It is designed for use with the RDA series of enclo-

sures, in a AMX Lighting™ modular digital dimming system. The RDM-FDB

module's 120, 240, and 277 VAC ratings are CE, UL, and C-UL approved.

RDM-FDB UL and C-UL Ratings

• 120 VAC, 1920 W

• 240/277 VAC, 1920 W

Suggested Dimmed Loads

• Most 3-wire dimmable fluorescent ballasts

• Lutron

Hi-Lume

FDB Ballasts

• Lutron Eco-10

Ballasts

Specifications:

• Dimensions (HW): 10.0" x 2.75" (25.4 cm x 6.99 cm)

• Dimmed output protected by a 250 mA GMA 5 x 20 mm fuse

• Phase dependant

• Use wires rated at 75°C (167°F)

• Torque terminals to 20 in-lbs. (2.3 N/M)

• Max. wire size: 10 AWG (4 mm²)

• Wire stripping length: 0.28" (7 mm)

• Weight: .72 lbs. (0.327 kg)

•BTU/hr: 5

• Control current: 85 mA @ 12 VDC

• For use with FDB ballasts

Caution: Pre-Installation Notes

• All Class 1 wiring must be connected to proper terminals.

• All control wiring must be connected to proper terminals.

• Disconnect power while installing or connecting the unit.

• Keep top and bottom air vents clear at all times.

• Use field installed copper conductors.

• All electrical ratings are for continuous duty.

• For indoor use only.

• This module may require extra power from the AXlink connection or an

external power supply connected to the control card.

Connecting the RDM-FDB to the AMX Lighting Master

Lighting Appplication Drawing

FIG. 1 RDM-FDB

Mounting points

Fuse

Positive air

gap relay

Dimmed out

Relay

Line in (hot)

Switched out

Low-voltage

control wiring: 4-pin

connector to AMX

Lighting master

controller

Ballast A

FIG. 2 RDM-FDB connections

FIG. 3 RDM-FDB wiring configuration

Pin 4 (GND)

Pin 3 (RLY)

Pin 2 (DIM)

Pin 1 (+12 V)

RDM-FDB 4-pin module connector

3 (-)

2 (AC)

1 (+)

4-pin plug from RDM series module

Note: The 4-pin plugs from the module connector

to the 4-pin connector on the master (black plug cover facing up).

BALLAST

Ballast

Circuit breaker

panel

The fuse protects the dimming

circuit from a low impedance

load.

• The fuse would blow if it

were incorrectly wired

• Catastrophic ballast failure

• Reversing switched and

dimmed circuits

• Reversing dimmed and

line circuits.

The dimmed output must be

connected to a high impedance

load.

All neutrals are

common to the

Neutral block in the

enclosure. Provide

a separate neutral

for each load.

Neutral

Line in (HOT)

Switched

Dimmed

Florescent

Ballast

Neutral

1 2

Installation Sheet 1

Sommario

Pagina 1 - Installation Sheet

Installation SheetRDM-FDB Single Channel Lutron FDB Ballast Dimmer1920 WThe RDM-FDB Single Channel Ballast Dimmer is a 1920 W positive air gap relay a

Pagina 2

AMX Corporation reserves the right to alter specifications without notice at any time. For full warranty information, refer to the AMX Instruction Man

Commenti su questo manuale

Nessun commento

AMX RDM-FDB Manuale Utente

Navigare online o scaricare Manuale Utente per no AMX RDM-FDB. AMX RDM-FDB User's Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi no AMX RDM-FDB