AMX RDC-PDC Manuale Utente Scaricare il pdf

Installation Sheet

RDC-PDC Control Card, Dual or Three Phase

(120 or 240 VAC)

The RDC-PDC Control Card module controls up to six dimmable channels

with six satellite connectors (for RDM series dimmer or switching modules).

The RDC-PDC is controlled by AXlink, PROlink, or by dry contact closures.

The RDC-PDC is designed for use with Radia enclosures, in a modular dig-

ital dimming system. The module's 120 and 240 VAC ratings are CE, UL,

and C-UL approved.

RDC-PDC UL and C-UL Ratings:

Control Input:

• AXlink

• PROlink

• Eight dry closures

Control Output:

• Six control ports

• Max. total control current at 300 mA

Power Inputs:

• Line 1 (channel 1 and 4)

• Line 2 A (channel 5)

• Line 2B (channel 2)

• Line 3 (channel 3 and 6)

• Neutral

Specifications:

• Dimensions (HW): 10.0" x 2.75" (254.0 mm x 69.85 mm)

• 12 VDC power (optional)

• Torque terminals to 20 in-lbs. (2.3 N/M)

• Max. wire size: 10 AWG

• Wire stripping length: 0.28" (7 mm)

• Weight: 1.5 lbs. (0.68 kg)

• Power consumption: 50 mA @ 120 VAC

25 mA @ 240 VAC

Button/Jumper Information:

• RESET button: By pressing the RESET button, located on the RDC-

PDC circuit board, it is possible to restart the processor without having

to power-down the unit or disconnect AXlink or PROlink. RESET does

not affect saved presets or curve settings.

• MEMORY PROTECT on/off jumper: The MEMORY PROTECT

jumper is set to Off by default. To protect saved curve settings and pre-

sets from accidental recording, put the jumper in the On position.

Caution: Pre-Installation Notes

• All Class 1 wiring must be connected to proper terminals.

• All control wiring must be connected to proper terminals.

• Disconnect power while installing or connecting the unit.

• Keep the top and bottom air vents clear at all times.

• Test loads for shorts before connecting.

• Use low-voltage wires with a 300 volt rating or greater.

• Use field-installed copper conductors.

• All electrical ratings are for continuous duty.

• For indoor use only.

• AC lighting loads only.

Connecting RDM Series to the AMX Lighting Master

Connecting AXlink

Connect the 4-pin captive-wire AXlink connector from the RDC-PDC to the

Central Controller for AXlink control of the dimming system.

Connecting PROlink:

Connect the orange 4-pin captive-wire PROlink connector from the RDC-

PDC to a PRO-DP8 PROlink wall panel.

FIG. 1 RDC-PDC control card

Line inputs

(factory wired)

Mounting

points

Reset button

Memory Protect

jumper

AXlink connector

PROlink connector

LED indicators

Control ports

Dry closure

contacts

AXlink DIP

switch

PROlink DIP

switch

FIG. 2 Connecting RDM series

FIG. 3 AXlink wiring

FIG. 4 PROlink wiring

Pin 4 (GND)

Pin 3 (RLY)

Pin 2 (DIM)

Pin 1 (+12 V)

RDC-PDC 4-pin module connector

4-pin plug from a RDM series module

Note: The 4-pin plugs from the module

connector to the 4-pin connector on the

master (black plug cover facing up).

PWR

AXP

AXM

GND

PWR

AXP

AXM

GND

Central

RDC-PDC

Controller

(optional)

PRO-DP8 Pack 1 Pack 2

+12

PR+

PR-

GND

+12

PR+

PR-

GND

1 2 3 4

Sommario

Pagina 1 - Installation Sheet

Installation SheetRDC-PDC Control Card, Dual or Three Phase(120 or 240 VAC)The RDC-PDC Control Card module controls up to six dimmable channels with s

Pagina 2 - Connecting Dry Closures

2 RDC-PDC Control Card, Dual or Three PhaseConnecting Dry ClosuresUse the 8 (+ common) dry closures with a WPD8 eight-button wall panel. Each conta

Pagina 3

RDC-PDC Control Card, Dual or Three Phase 3FIG. 8 Method BFIG. 9 Method CFIG. 10 Method DMethod BRDC-PDC/120 3-phase, 6 switchesMethod CThree phase

Pagina 4

AMX Corporation reserves the right to alter specifications without notice at any time. For full warranty information, refer to the AMX Instruction Man

Commenti su questo manuale

Nessun commento

AMX RDC-PDC Manuale Utente

Navigare online o scaricare Manuale Utente per no AMX RDC-PDC. AMX RDC-PDC User's Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi no AMX RDC-PDC