AMX RE-DM6 Specifiche Pagina 15
- Pagina / 90
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Radia Eclipse Dimmer Modules
7
RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules
Caution: Pre-Installation Notes
All Class 1 and 2 wiring must be connected to their dedicated terminals.
Class 1 wiring should be connected through the top of the enclosure, and Class 2 wiring through the
bottom.
Load conductors must be same size as line conductors, regardless of connected load.
Disconnect power while installing or connecting the unit.
Keep top and bottom air vents clear at all times, and maintain 12” (30.48 cm) clearance around the
top and bottom.
Test loads for shorts before connecting.
Class 2 wiring must be rated 300V or higher.
For indoor use only.
AC lighting loads only.
Line-In Connections
Using two feeds for Line 1 and Line 2 provides two 2400 W inputs.
Jumping Line 1 and Line 2 provides a single 2400 W input (FIG. 7)
This unit should be installed only by qualified electrical personnel, and in compliance
with all national electrical codes, local codes and ordinances.
To prevent possible personal injury or death, disconnect power to the enclosure at
the breaker box before attempting to work with any AMX Lighting modules.
To prevent possible personal injury or death, disconnect power to the enclosure at
the breaker box before attempting to install any AMX Lighting modules.
FIG. 7 Line-In Connections for the RE-DM6
Dual 2400 W Inputs without jumper
Single 2400 W Input with jumper
- Radia Eclipse Dimmer 1
- Table of Contents 5
- Radia Eclipse Dimmer Modules 9
- RE-DM4 Specifications 10
- Suggested Loads 10
- Line-In Connections 11
- RE-DM6 Specifications 14
- Suggested Installation Loads 14
- AMX Lighting Systems 17
- Installation 19
- LEFT SIDE FRONT RIGHT SIDE 20
- SIDE VIEW 21
- RDA-ENC6B 21
- TOP VIEW 21
- High-Voltage Connections 23
- Connect to neutral block 24
- Low-Voltage Connections 28
- Position Value 30
- Connecting Dry Closures 31
- Failsafe Input 31
- Emergency Input 31
- Default Settings 32
- Overview 33
- Lighting System Link 33
- Main Lighting System Page 34
- Device Configuration Page 35
- FIG. 32 Presets section 36
- FIG. 34 New Preset button 37
- Software 39
- Preset Status 40
- Lighting Systems Overview 41
- Programming Commands 42
- Channels 44
- SEND_STRINGs 44
- Ramp Dimmers Up 45
- Ramp Dimmers Down 45
- Stop Ramping Dimmer 46
- Ramp Active Preset Up 46
- Ramp Active Preset Down 46
- Stop Ramping Preset 47
- Recall Preset 47
- Record Preset 47
- Level Status 47
- Set Curve 48
- Curve Status 48
- Set Low End 48
- Low End Status 48
- Dimmer Status 49
- Set Default Level Time 49
- Set Default Preset Time 49
- Set Default Ramp Time 50
- Ramp To Level 50
- Undefine Dimmer 50
- Phase Query 51
- Version Query 51
- Factory Default 51
- SEND_COMMANDs 52
- Ramp Preset Down (NEW) 53
- Stop Ramping Preset (NEW) 53
- Curve Status (NEW) 54
- Set Low End (NEW) 54
- Low End Status (NEW) 54
- Reboot (NEW) 54
- Ramp to Level 55
- Undefine Dimmer (NEW) 55
- Phase Query (NEW) 56
- FIG. 38 Basic dimming curve 58
- Curve Configuration 59
- Standard Dimming Curve (1) 60
- Economical Dimming Curve (2) 62
- 0-10VDC Curve (3) 63
- Curve 3 at 120 VAC 64
- Curve 3 at 240 VAC 64
- Curve 3 output in volts DC 64
- 0-12VDC Curve (4) 65
- Lutron FDB Curve (5) 66
- FIG. 56 Curve 5 at 240 VAC 67
- Advance Mark VII Curve (6) 68
- 12% Roll Off (7) 69
- 19% Roll Off (8) 71
- 33% Roll Off (9) 72
- S-Curve #1 (A) 74
- Log-Curve #1 (B) 75
- Log-Curve #2 (C) 77
- S-Curve #2 (D) 78
- 10% Off Curve (N) 79
- Always OFF Curve (O) 80
- Always ON Curve (F) 81
- Curve F at 240 VAC 82
- Curve R at 120 VAC 83
- Curve R at 240 VAC 83
- Curves 5 & B at 120 VAC 83
- Curves 6 & C at 120 VAC 84
- Curves A & D at 120 VAC 85
- Curves A & D at 240 VAC 85
- Appendix B: Troubleshooting 87
- Hardware Issues 88
- Increase Your Revenue 90
Bosch LTC-2915-91 manuály
Uživatelské manuály a uživatelské příručky pro Televizory a monitory Bosch LTC-2915-91.
Poskytujeme 1 manuály pdf Bosch LTC-2915-91 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale