AMX DXLink Multi-Format Wallplate Manuale delle Istruzioni Pagina 109
- Pagina / 141
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Appendix B – Telnet (Terminal) Commands
109
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
To establish a terminal connection via NetLinx Studio:
1.
In the Online Tree, select the DXLink unit and right-click to access the short-cut menu.
2. Select Launch Telnet Window via NetLinx Studio.
The Telnet window opens and the welcome banner appears.
3. At the prompt (>), type the Telnet command and press Enter.
Telnet Username and Password
The following commands are used to set the Telnet username and password for a Telnet connection:
Set Telnet Username
Set Telnet Password
By default, both the username and password are blank (empty strings). Performing a factory reset on the device with the
Pushbutton will return these values to that default. For details, see page 70.
Username – Setting the Username will have no effect if the password remains blank (empty string). That
is defining the username alone will not result in Telnet prompting for a user login.
Password – Setting the Password will cause Telnet to prompt for a user login, whether the username has
been defined or not. If the username has been defined, this value must be entered.
However, since the password can be set independently of the username, it’s possible to have a password
defined, but the username still at its default (blank, empty string). In this case do not enter anything for the
username when prompted. Simply press Enter, which will then present the password prompt. Here, the
defined password must be entered in order to successfully open the Telnet session.
Additional Notes
Both the Telnet username and password are case-sensitive.
Three consecutive, unsuccessful attempts to log in to Telnet will cause the Telnet window to close.
Re-launching Telnet will again present the login prompt, with a fresh “batch” of login attempts.
If a Telnet login fails because of an incorrect username, an “Invalid Password” message will appear
(as opposed to an “Invalid Username” message).
The username and password are saved after reboot or power cycle.
The username and password are deleted/removed after a factory reset.
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Prodotti e manuali riguardandi Ricevitore AMX DXLink Multi-Format Wallplate
Ricevitore AMX UDM-0102 Manuale Utente
(3 pagine)
(3 pagine)
Ricevitore AMX UDM-0102 Manuale Utente
(2 pagine)
(2 pagine)
Ricevitore AMX MX8 Manuale delle Istruzioni
(22 pagine)
(22 pagine)
Ricevitore AMX DXLink HDMI Manuale Utente
(6 pagine)
(6 pagine)
Ricevitore AMX MX16 Manuale Utente
(2 pagine)
(2 pagine)
Ricevitore AMX MX8 Manuale Utente
(2 pagine)
(2 pagine)
(6 pagine)Bosch LTC-2915-91 manuály
Uživatelské manuály a uživatelské příručky pro Televizory a monitory Bosch LTC-2915-91.
Poskytujeme 1 manuály pdf Bosch LTC-2915-91 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale