Amx Signature Series NetLinx Integrated Controller NI- Manuale Utente Pagina 34
- Pagina / 156
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Configuration and Firmware Update
24
NI-3101-SIG Signature Series NetLinx Integrated Controller
4. Note the obtained IP Address (greyed-out and read-only). This information is later entered into the
Master Communication Settings dialog and used by NetLinx Studio v 2.x to communicate to the
Master via an IP. This address is reserved by the DHCP server and then given to the Master.
5. Verify that NetLinx appears in the Host Name field (if not, then enter it in at this time).
6. Click the Use DHCP radio button from the IP Address section (if not greyed-out).
7. Click the Set IP Information button to retain the IP Address from the DHCP server and assign it to the
on-board Master. A popup window then appears to notify you that Setting the IP information was
successful and it is recommended that the Master be rebooted.
8. Click OK to accept the change to the new IP/DNS information.
9. Click the Reboot Master button and select Ye s to close the Network Addresses dialog.
10. Click Reboot from the Tools > Reboot the Master Controller dialog, and wait for the System Master to
reboot and retain the newly obtained DHCP Address. The STATUS and OUTPUT LEDs should begin to
blink alternately during the incorporation. Wait until the STATUS LED is the only LED blinking.
11. Press Done once until the Master Reboot Status field reads *Reboot of System Complete*.
12. Complete the communication process by continuing on to the Communicating with the NI Device via an
IP section on page 26.
Assigning a Static IP to the NetLinx Master
1. Select Diagnostics > Network Addresses from the Main menu to access the Network Addresses dialog
(FIG. 22).
DO NOT enter ANY IP information at this time; this step only gets the System Master
to recognize that it should begin using an obtained DHCP Address.
If the IP Address field is empty, give the Master a few minutes to negotiate a DHCP
Address with the DHCP Server, and try again. The DHCP Server can take anywhere
from a few seconds to a few minutes to provide the Master with an IP Address.
Verify that these IP values are also entered into the related fields within either the
IP Settings section of the System Connection page (on the touch panel) or within the
Address field on the web browser.
Verify that the Controller has an active LAN connection before beginning these
procedures.
FIG. 22 Network Addresses dialog (for a pre-obtained Static IP Address)
System Address
reflects the value
set in the Device
Addressing tab
Used to retain an
IP Address
- NI-3101-SIG 1
- Table of Contents 10
- Introduction 11
- NI-3101-SIG Specifications 12
- Installation and Upgrading 15
- Connections and Wiring 17
- AXlink Port and LED 18
- Wiring Guidelines 19
- Relay connections 21
- IR / SERIAL (Ports 5-8) 22
- IR / SERIAL (Ports 9-16) 22
- 8 76 45 321 22
- LAN RJ-45 Pinouts and Signals 23
- ETHERNET 24
- Setting the System Value 28
- Device Addressing dialog 31
- TCP/IP Settings dialog 37
- New TCP/IP Setting dialog 37
- NetLinx Security Terms 44
- Browser Application Frames 45
- Log In/Log Out fields 46
- Web Control 47
- Security Features 48
- System Level Security Page 50
- Port Communication Settings 52
- ICSP Authentication 53
- Manage Group Page 54
- System Settings 61
- Manage System Page Components 62
- Modify System/Date dialog 64
- Change System Number dialog 65
- Control/Emulate dialog 66
- Manage System - Server 71
- Server Certificate Entries 75
- Export SSL Certificate dialog 79
- Import SSL Certificate dialog 80
- Network Settings dialog 81
- URL List dialog 82
- Device Number dialog 83
- Log dialog 84
- Removing a license 86
- 2. Click the Remove button 86
- Discovery Pages 90
- Manage Device Bindings page 96
- View Discovered Devices page 98
- Select Device Module page 99
- Add New Device page 99
- 1. Launch a web browser 102
- Certificate Import Wizard 104
- Connection Details dialog 106
- Overview 109
- NetLinx Security Features 109
- Access Rights Menu 114
- Main Security Menu 119
- Help menu 121
- Help Menu Options (Cont.) 122
- Logging Into a Session 123
- Setup Security 124
- Programming 125
- Master Send_Commands (Cont.) 126
- Using the ID Button 127
- Configuration Port Commands 128
- SET DNS [0:1:0] 133
- SET IP [0:1:0] 134
- ESC Pass Codes 141
- RS232/422/485 Ports Channels 142
- RS-232/422/485 Send_Commands 142
- IR / Serial Ports Channels 146
- IR/Serial Send_Commands 146
- Input/Output Send_Commands 152
- Troubleshooting 153
Prodotti e manuali riguardandi Hardware Amx Signature Series NetLinx Integrated Controller NI-
Hardware Amx AXR-IRSM+ Manuale Utente
(2 pagine)
(2 pagine)
Hardware Amx AXC-INP8 Manuale Utente
(8 pagine)
(8 pagine)
Bosch LTC-2915-91 manuály
Uživatelské manuály a uživatelské příručky pro Televizory a monitory Bosch LTC-2915-91.
Poskytujeme 1 manuály pdf Bosch LTC-2915-91 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale